mini - PACCS Personal duress alarm system
The mini - PACCS “man-down” is a microprocessor-controlled
personal emergency transmitter designed for use by guards and
security officers in prisons and institutions, or by people
working alone in industrial and other high-risk facilities.
The mini - PACCS has five types of events: Distress –
by depressing the two emergency buttons simultaneously, man-down
– when the wearer falls down, pull-cord – when someone
attempts to pull the transmitter off the wearer, test –
for testing the transmitter and tamper – when an unauthorised
person opens the transmitter.
For maximum security, the Mini - PACCS uses a unique, factory
programmed, randomly selected 24-bit digital alarm ID code during
each transmission. This code is selected from 16 million possible
code combinations and is therefore unique and virtually impossible
to accidentally reproduce. A smart anti-collision algorithm
prevents signal jamming by simultaneous transmission from multiple
devices.
The fully supervised repeater issues a test report on an hourly
basis, indicating faults such as power failure, low battery
charge and tampering.
The mini - PACCS can be integrated into any alarm system, or
paging system, and it supports an exceptionally wide range of
detection devices.
In case an event is detected, mini - PACCS automatically issues
a report to the monitoring station, simultaneously transmitting
digital and voice alerts to pre-programmed private telephones,
mobile phones and/or pagers. All this functionality is packed
into a single wireless solution, which is as easy to deploy
as it is to operate.
The mini - PACCS wireless system is ideal for SME’s and
SoHo applications, as well as industrial, processing and medical
sites and is easily installed, being set up as pre-configured
to work out of the box.
mP-Belt T( Man Down Transmitter)
Transmission Type: Radio Frequency (RF)
RF Frequency (MHz): 315MHz, 418 MHz or 433.92
MHz
Transmitter s ID Code: 20- bit ID 4 –bit
Event ID
Modulation Type: Pulse width modulation
Over all message length: 36 bit
Alarm messages: Tilt activated, pull- cord
disconnected, panic alarm, Test, each with separate ID
Supervision: Option for automatic reporting
at I – hour intervals
Power Source: 3.6 v, lithium battery, size
½ AA/ 1.2 Ah, ( Tadiran TL – 2150 or equivalent)
Current Consumption: 15µ A standby, 10Ma
( Operation).
Battery Life: 3- 4 years in normal use
Battery supervision: Battery test and reporting
every hour
Operating temperature: 0º C to 49º
C ( 32º F to 120ºF)
Dimensions ( H X WX D): 120 X 52 X 36 MM (
4-3/4X 2-1/16 X1-5/16in.)
With holster-3: 140 x 77 x 50 mm ( 5-7/16 x3-1/16
x1 -15/16 in.)
Housing: 3mm ABS PLASTIC BOX, Weather proof
Weight: Man – down – 138g ( 4.9
Oz.) Holster -3 -30g (1.05 0z.)
Color: Body – dark gray, buttons –
brown, pull cord – black
Compliance with Std: FCC part 15, CE ( ETS
300220, ETS 300683)
Accessories: light weight water – resistant
carry pouch holster -3. metal belt clip.
Pull cord with pin and cloth clip.
mP-Receiver 8: Wireless interface for Hard wire control
panels
RF SECTION
Front end module: Super heterodyne UHF Receiver.
Operating frequency ( MHz) : 315, 418 , 433.92,
868.95 and other UHF channels per local requirements in country
of use.
DATA PROCESSING SECTION
ID Codes: over 16,000,000 possible 24- bit
combinations
Total Message Length: 36bits(66 bits for code
secure devices)
ID learning capacity: 112 different ID Codes
Expander Bus: 4 wires (12V+, (-), DATA and
COMMON)
ELECTRICAL DATA
Zone outputs: 4, up to 100mA each, open- collector
type
Status outputs: 4, up to 100Ma each, open –
collector type
Output No .1 Modes: pulsed ( 2 seconds) or
toggle, selected with DIP switch
Output Polarities: N.0 or N.C., Selected with
DIP Switch
Tamper Switch Ratings: 0.1A/30VDC.
Input Voltage Range: 10.5 – 16VDC
Current Drain ( @ 12 VDC): 45Ma
PHYSICAL
Operating Temperatures: 0º C to 49ºC
( 32º ì F to 120º ì F).
Dimensions ( H X W XD): 108 X 165 38 mm (4
– ¼ x 6-1/2 x 1-1/2”)
Weight ( Including rigid antenna): 214g ( 7.5oz).
Compliance with standards: Meet FCC part 15,
ETS 300-220, ETS 300- 683 and MPT 1340 requirements
AUXILIARY EQUIPMENT
MCL -8: Eight – output Zone expander
RL - 8: Eight – relay interface unit.
Return
Top
